Blogs – Page 3 – NDUME LIMITED

Cultivator Weed Buster Trailed

The Ndume weed buster cultivator is the ideal secondary tillage machine. In line with modern thinking, the weed buster slices off the weeds, breaks down the clods with a minimum loss of moisture and soil degradation.Tines are “C” section type made from plate formed into a channel and boxed in at the back for extra strength. Each tine is spring loaded and will break away if rocks or roots are...

Cultivator Weed Buster Mounted

The Ndume weed buster cultivator is the ideal secondary tillage machine. In line with modern thinking, the weed buster slices off the weeds, breaks down the clods with a minimum loss of moisture and soil degradation. Tine legs are made of steel channel boxed in at the back for maximum strength, each tine is fitted with a coil spring. Tines can be supplied with a 9” sweep or a 2”...

Standard Chisel Plough 11-15 Tine

Chisel-ploughing the Ndume way means: More Acres cultivated with less fuel used.Leaves your moisture from the previous season underground - where it should be.Moisture penetrates deep down into the soil profile when it rains.Eliminates hard pans caused by conventional ploughing.Soil erosion is cut down to a minimum.Leaves your field in a state that means one harrowing is usually enough for a seed bed.Generally crop yields will be increased due to...

Standard Chisel Plough 5 – 9 Tine

Rip-on-Row Chisel Pough

2, 3 or 4-TinesDesigned to Save You Money! Don’t beat your soils to death!It has now been proved beyond all doubt that the less you disturb your soils the more fertilethey become. Conservation Tillage conditions your soils into a state that allows the soils tocollect and retain the moisture and rainfall that is available. We call this “Putting Rain in theBank”Chisel Ploughing the NDUME way means: Moisture penetrates deep down...

Auto Reset Tine

The standard Ndume chisel plough tine has a shear pin protection system that breaks if a tine encounters a rock or roots in the soil. If the shear pin breaks the driver has to stop, get off his tractor and replace the shear pin. This is time consuming and hard work. The new Ndume auto reset tine has an automatic break away system. When a tine hits a rock or...

Inline Chisel Plough 2 to 5 Tine

The Ndume chisel plough is designed to work behind a 30 to 80HP two or four wheel drive tractor. Tines are the easy-flow low draught type. It is designed with a wheel at the rear to;1) depth-control the plough, and 2) eliminate the side draught caused by thefirst tine. This wheel is adjustable for depth and steering.Conventional ploughing requires two tractor wheels in the previous furrow which causes compaction. With...

Contine Ripper

The Contine Ripper is designed to rip in between rows of coffee, sisal etc. The tine is designed to get under the side of the tree or brush without damaging it. This ensures good moisture penetration to the root system of the plant. The tines are protected by a 5/8” shear bolt system, and tinesare adjustable across beam to accommodate different crop row widths.

Chisel Plough Spring Loaded

Chisel-ploughing the Ndume way means: More Acres cultivated with less fuel.Leaves your moisture from the previous season underground - where it should be.Incorporates crop residue into the topsoil where it should be.Eliminates all pans caused by conventional ploughing.Reduces erosion because moisture can penetrate deep down.Leaves your field in a state that means one harrowing is usually enough for a seed bed.TECHNICAL SPECIFICATIONSThe Main Frame Material• 100mm x 100mm high stress...

2 to 5 Tine Ridger

Simple heavy duty Ridger wings fitted to tines (the same tine as fitted to Ndume Chisel Ploughs) protected by a 5/8” Shear Bolt system.Tines are adjustable across beam to accommodate different sized seed beds.Ridger wings are detachable, therefore easily replaced if damaged.

Water Wheel

The Ndume Water Wheel pump will pump water from a small stream 24 hours a dayefficiently. All you require is a 6ft fall – easy to construct on a small stream – and a reasonable flow of water. The only daily maintenance requirement is greasing.The pump is driven directly off the wheel center shaft and is a simple reliable horizontallyopposed piston pump. There are two stroke settings, one for high...

Turbo Pump

THE NDUME TURBO-WATER PUMP NO FUEL – MINIMAL MAINTENANCE The NDUME TURBO WATER PUMP provides a simple, cheap and reliable method of pumping water from streams and rivers. It utilizes the water as the sole driving force. NO FUEL WHATSOEVER IS REQUIRED. All that is needed is a flow of approximately 2 cusec or more and a fall of 2 – 3 feet (2 cusec – a reasonably fast flowing...